Airline rail with piping groove - 1.5 meters
The 1.5-meter-long piping rail with airline profile is suitable for accommodating piping, which is often used to attach awnings, flexible sun canopies, or tarpaulins.
The keder groove in the airline rail allows the awning or sun canopy to be securely attached to the vehicle, and the airline rail can be used for additional fastening options.
The diameter of the keder groove is 8 mm, and that of the keder opening is 3 mm.
We recommend keder of at least 4 mm and a maximum of 7.5 mm.
Our piping rail is made of uncoated aluminum. We also offer anodized versions on request.
In addition, the rail is undrilled. It can be drilled at the desired points or glued without drilling.
There is a wide adhesive bead on the underside for gluing the airline rail. We recommend Sikaflex 554 - black or Sikaflex 554 white.
End caps: The rail can be ordered with matching end caps (left and right), which are available as an option. The keder groove remains accessible even when the end cap is mounted, as the groove in the end cap is open.
Technical properties
| Length: |
1.5 meters (1,490 mm +/- 3 mm) |
| Rail width: |
44 mm |
| Installation height: |
11.3 mm |
| Hole diameter: |
20 mm |
| Hole/grid spacing: |
25 mm |
| Material: |
Aluminum - bare |
| Alloy: |
EN AW 6082 T6 |
| Weight: |
0.6 kg/m |
| Mounting hole: |
Undrilled |
| Made in: |
Germany |
| Manufacturer: |
allsafe |
Load capacities of the airline rail - Kerderschiene - Light
The airline lashing rail can be used in conjunction with the Single Stud, Automotiv, and Double Stud fittings in accordance with DIN 75410, ISO 27955, and ISO 27956.
With the Quattro Stud fitting, the airline rail can even be used in accordance with DIN EN 12640 up to 1000 daN.
Airline rails are used in conjunction with locking bars, lashing straps, or end fittings for load securing.
The following load capacities are achieved with the following fittings:
| End fitting/fitting |
Standard |
Load capacity |
| Single stud fitting - Item no.: 102033 |
ISO 27956 |
300 daN |
|
ISO 27955 |
350 daN |
| Kerl 500 - Item no.: 102211 |
DIN 75410-1 / ISO 27956 |
400 daN |
|
ISO 27955
|
350 daN |
| Double Stud/Double End Fitting - Item No.: 102036 |
DIN 75410-1 |
400 daN |
|
ISO 27956 |
500 daN |
| Quattro Stud Fitting - Item no.: 102176 |
ISO 27956 |
800 daN |
|
EN 12640
|
1,000 daN |
Fastening of the airline rail
The above permissible load capacities are achieved under the following conditions:
It is essential that the airline rail is adequately fastened to the substrate!
The maximum load capacity of the airline rail depends on the following factors:
Not only the strength, material properties and, depending on the fastening, the surface is decisive for the load capacity; the type of fitting used is also of great importance.
If the airline rail is to be screwed in place, we strongly recommend that you follow the installation guidelines provided by the manufacturer, allsafe.
These state that
countersunk screws must be set at a distance of 75 mm for airline rails with a metric grid spacing of 25 mm!
Screws with a strength of at least 10.9 must be used, with washers and self-locking nuts. Since the use of nuts and washers is often not possible in vehicle construction, rivet nuts or threaded anchor nuts are used as an alternative.
The airline rail as a light profile is usually fastened with M5 countersunk screws.
Another fastening option is gluing.
This airline rail is not pre-drilled and can therefore be glued with Sikaflex 554, for example, or drilled at the desired points.
We only recommend riveting or fastening with other head screws to a limited extent, as the protruding rivet head or screw head makes it impossible to insert the end fittings; more precisely, the slot nuts cannot be pushed through.
The installer of the load securing aids is responsible for the installation and the resulting possible load!
Applications of ISO and DIN standards:
- ISO 29755 = lashing point standard in passenger
cars - ISO 29756 = lashing point standard
in panel vans (transporters) - DIN 75410-1 = lashing point standard on flatbed vehicles up to 3.5 t
- EN 12640 = lashing point standard on flatbed vehicles from 3.5 t
Where does the airline rail with a bead groove come from?
This airline rail is manufactured by the company allsafe in Germany.
This is expressly not a Chinese import!
The advantages of the airline rail summarized
- only
44 mm wide - groove for adhesive
- low weight due to
aluminum - high
tensile strength - versatile applications (not only for load securing)
allsafe GmbH & Co. KG
Gerwigstraße 31
78234 Engen
sales@allsafe-group.com
Payment by Invoice | 
How to find our store
info@kurierbedarf.com
Purchasing for Swiss customers
