Aluminum roof rack for Nissan NV300 and Nissan Primastar - L1
The roof rack for the Nissan NV300 built between 2016 and 2021 and Nissan Primastar built from 2021 onwards, with a wheelbase of 2,925 mm, is made of aluminum.
The lightweight and aerodynamic aluminum roof rack comes with a loading roller and front spoiler.
The loading roller makes it easier to load and unload long, bulky goods, and the front spoiler reduces driving noise and minimizes fuel consumption.
Roof racks significantly increase the storage space of your van. This makes it possible to transport more goods or tools and use the cargo space more effectively.
Installation time with 2 people is approx. 45 minutes.
The load capacity approved by the vehicle manufacturer is 150 kg. However, the tested load capacity of the roof rack is up to 180 kg.
For vehicles built in 2014 or later with the following vehicle dimensions:
| Designation |
Rear door(s) |
Wheelbase |
Overall length |
Vehicle height |
Roof rack size |
| L1H1 |
Tailgate |
2,925 mm |
4,600 mm |
1,971 mm |
2,600 x 1,580 mm |
| L1H1 |
Swing doors |
2,925 mm |
4,600 mm |
1,971 mm |
2,600 x 1,580 mm |
Note: The vehicle length can be found in the vehicle registration document under item 18, the vehicle height under item 20, and the year of manufacture under item 6. (Applies to German vehicle registration documents)
Important note: The loading roller can only be installed on vehicles with rear doors (wing doors). Not suitable for vehicles with tailgates! For vehicles with factory-fitted roof rails, the roof rails must be removed.
Features and characteristics of the roof rack
The basic equipment includes the mounting feet, front spoiler, and loading roller.
The workmanship is high quality and, with its improved aerodynamic design, the roof rack saves fuel and generates less noise when driving at speed.
The system is robust and ideally suited for intensive use.
Thanks to the innovative mounting system, the crossbars can be inserted and positioned flexibly.
With the well-designed screw system, the roof rack can be mounted in no time.
Features at
a glance - Basic equipment includes mounting feet, front spoiler, and loading
roller - High quality with aerodynamically improved design for lower fuel consumption and less noise
- Robust system - For intensive use
- Innovative mounting system -
Quick to install by sliding in the crossbars and using the sophisticated screw system - Can be expanded with extensive accessories
Optional accessories for the Cruz aluminum roof rack The roof rack can be expanded
with a wide range of accessories, including components from other manufacturers, such as Rhino Products. Expandable accessories
include: ladder holders, load secures for fastening with lashing straps, transport tubes, or, depending on the vehicle, a rear door ladder.
All accessories are supplied with the appropriate mounting hardware, where necessary.
Load securing restraints
The four 10 cm high load securing restraints are limiters that prevent the goods being transported from rolling back and forth. Lashing straps
can also be attached to the load securing restraints to secure the load.
Ladder holder
With the ladder holder, it is possible to secure ladders quickly and easily without the complicated handling of lashing straps. Up to 4-piece
ladders can be transported.
The scope of delivery consists of one pair and always includes two ladder clamps for the front and rear.
The dead weight is: 2.5 kg
Transport tube
The aluminum transport tube is suitable for transporting long goods such as copper pipes or roof battens. The transport tube
is available in lengths of 2 m, 3 m, and 4 m. There are closable openings at the ends.
Alternatively, the Rhino transport tube can also be mounted up to a length of 5 m.
Walkway
The walkway is suitable for walking on the roof rack.
It is easily and simply attached to the crossbars with clamps.
For longer vehicles, several sections are supplied.
Installation of Cruz aluminum roof racks
The Cruz roof rack is mounted on the fixing points specified by the vehicle manufacturer.
Plastic caps can be seen on the roof of your van. The fixing points are located underneath these caps.
These plastic caps are removed and the mounting feet are screwed into place. The
mounting feet must first be mounted on the roof rack. We will be
happy to send you the installation plan, or you can view it under "Technical Details."
Cruzber
Pol. Ind. Las Salinas II, parc. 12
14960 Rute (Córdoba) Spain
Spanien
info@cruzber.com
Payment by Invoice |
How to find our store
info@kurierbedarf.com
Purchasing for Swiss customers
